客户在求租冷再生机使用过程中，不可避免地会出现消耗和磨损，其中，冷再生机输送带特别容易出现问题，运行时间长，可能出现打滑现象，影响工作效率。下面冷再生机出租厂家来分析下打滑的原因和解决办法。

Customers inevitably experience consumption and wear during the use of a cold recycling machine, among which the conveyor belt of the cold recycling machine is particularly prone to problems, long operation time, and may slip, affecting work efficiency. Let's analyze the reasons and solutions for the slipping of the cold regeneration machine rental manufacturer below.

1、初始张力太小。

1. The initial tension is too low.

输送带离开滚筒的张力不够，会引起皮带打滑。一般来说，这种情况是在启动时发生的。如果你想解决它，你必须调整张力装置和增加初始张力。

Insufficient tension of the conveyor belt leaving the drum can cause the belt to slip. Generally speaking, this situation occurs during startup. If you want to solve it, you must adjust the tension device and increase the initial tension.

2、摩擦力是不够的。

2. Friction is not enough.

传动滚筒与输送带之间的摩擦力不足以引起滑动。造成这种现象的主要原因是输送带上的水或环境潮湿。解决方法：在气缸中加入一些松香末。注意不要用手而应用鼓风设备吹入，以免发生事故。

The friction between the transmission drum and the conveyor belt is not sufficient to cause sliding. The main reason for this phenomenon is the water on the conveyor belt or the humid environment. Solution: Add some rosin powder to the cylinder. Be careful not to use your hands and blow in with an air blowing device to avoid accidents.

3、轴承损坏

3. Bearing damage

尾部滚子轴承损坏或不旋转。造成损坏的原因是机器尾部太浮、太沉，不能及时修理和更换损坏的或不灵活的部件，这导致由打滑引起的阻力增加。

The tail roller bearing is damaged or does not rotate. The reason for the damage is that the tail of the machine is too floating and heavy, and damaged or inflexible components cannot be repaired and replaced in a timely manner, resulting in increased resistance caused by slipping.

4、起步太快。

4. Starting too fast.

起动速度太快，不能打滑。这个时候可慢速启动。如果使用鼠笼电机，则可以移动两次，然后被，还可以有效地克服打滑现象。

The starting speed is too fast to slip. At this time, it can be started slowly. If a squirrel cage motor is used, it can be moved twice and then activated, effectively overcoming slipping.

5、输送带负荷过大。

5. The conveyor belt is overloaded.

输送带的负荷过大，超过电机能力也会打滑。打滑的优点是保护电机。否则，电动机将长期燃烧。但对于运行来说则是打滑事故。

The load of the conveyor belt is too large, and exceeding the motor capacity can also cause slipping. The advantage of slipping is to protect the motor. Otherwise, the motor will burn for a long time. But for operation, it is a slip accident.

以上是冷再生机时打滑的原因及方法相关信息的所有内容了，想要了解更多关于求租冷再生机相关内容，请继续关注浏览我们网站。

The above is all the information about the reasons and methods of slipping during the cold recycling machine. If you want to learn more about renting a cold recycling machine, please continue to follow and browse our website .