由于道路等级和结构不同，高等级公路作业时也可用相关类型的冷再生机，该再生机后部装有熨平板来完成再生料的摊铺，不需要平地机整平。当然水泥冷现场再生施工也有其注意事项，下面冷再生机出租厂家为您分析。

Due to different road grades and structures, relevant types of cold recycling machines can also be used for high-grade highway operations. The rear of the recycling machine is equipped with a screed to complete the paving of recycled materials, without the need for grader leveling. Of course, there are also precautions for recycling construction on the cement cold spot, and the following cold recycling machine rental manufacturer will analyze for you.

施工前应确定不均匀材料区域或路面厚度。须明确没有足够厚度或路基强度支撑再生车组重力的区域。这些强度不足的区域须在再生前纠正，否则铣刨机或其他冷再生设备有可能穿透路面造成施工延误和费用的增加。对再生前原道路进行预整形，严重变形的路面在再生前进行校正，使用平地机整平或熨平板摊铺后，可以保证再生厚度均匀，形状校正包括改变横坡和纵坡的小量调整。

The uneven material area or pavement thickness shall be determined before construction. It is necessary to identify areas where there is insufficient thickness or subgrade strength to support the gravity of the recycled fleet. These areas with insufficient strength must be corrected before regeneration, otherwise the milling machine or other cold recycling equipment may penetrate the pavement and cause construction delay and cost increase. The original road shall be pre shaped before regeneration, and the seriously deformed pavement shall be corrected before regeneration. After leveling with a grader or spreading with a screed, the thickness of regeneration can be uniform. Shape correction includes minor adjustment to change the cross slope and longitudinal slope.

对再生施工中所需的所有机械进行检查，检查各种施工材料是否足够满足再生路段施工的需要，检查机械操作人员是否已将所有与稳定剂添加量有关的数据输入微机控制系统中，再生路段是否有明确的导向标志，所有开始程序是否均已清楚。

Check all the machinery required in the regeneration construction, check whether various construction materials are sufficient to meet the needs of the regeneration section construction, check whether the mechanical operators have input all the data related to the stabilizer dosage into the microcomputer control system, whether the regeneration section has clear guide signs, and whether all the starting procedures are clear.

一旦施工开始，质检人员对施工状况进行一次检查，以获得预期的施工效果是非常重要的。摊铺后的再生结构层通常需要使用三种压路机来压实。

Once the construction starts, it is very important for quality inspectors to check the construction status to obtain the expected construction effect. Three types of rollers are usually used to compact the recycled structural layer after paving.

先使用一台重型压路机，采用高幅振动压实贯穿再生层底部，然后采用光轮压路机以低振幅振动模式压实新摊铺层的上部，后采用轮胎式压路机来完成整个结构层的压实。再生层面的装饰。

First, a heavy roller is used to compact the bottom of the recycled layer with high amplitude vibration, then the smooth wheel roller is used to compact the upper part of the new paving layer with low amplitude vibration mode, and then the tire roller is used to complete the compaction of the entire structural layer. Decoration of regeneration layer.

加入适量的水用轮胎压路机，将足够多的细料带出来填充粗颗粒料间的空隙，从而早再生层表面形成一层致密的防水构造。

Add an appropriate amount of water into the tyre roller to bring out enough fine materials to fill the gap between the coarse particles, so that a dense waterproof structure is formed on the surface of the early regeneration layer.

冷再生技术的应用在施工过程中很多工艺流程需要通过理论的完善和施工过程中的摸索进一步改进、发展，使水泥现场冷再生技术在沥青材料循环利用中发挥更为突出的作用。更多相关内容就来我们网站咨询吧！

The application of cold recycling technology in the construction process requires further improvement and development of many technological processes through theoretical improvement and exploration in the construction process, so that the on-site cold recycling technology of cement plays a more prominent role in the recycling of asphalt materials. More relevant content will come to our website Consult!