为了降低路面铣刨机的使用成本，在平时的施工过程中，要综合考虑科学使用和维护保养两个方面，做好以下几方面的工作。

In order to reduce the use cost of pavement milling machine, in the ordinary construction process, it is necessary to comprehensively consider the scientific use and maintenance, and do a good job in the following aspects.

合理使用刀具

Rational use of cutting tools

铣削深度越大，刀具与材料接触的时间越长，产生的摩擦热就越多。为了避免刀具硬质合金头的热腐蚀，需要增加冷却头的喷水量；当铣削深度较浅（6厘米以下）时，应减少冷却头的喷水量，以利于材料的输出，从而防止切削和铣削材料的接触，减少刀具的磨损。每运行6-8小时，检查刀具的转动和磨损情况，确保安装的刀具在刀架内自由转动。

The greater the milling depth, the longer the tool and material contact time, the more friction heat will be generated. In order to avoid the hot corrosion of the cemented carbide head of the cutting tool, it is necessary to increase the water spray amount of the cooling head; When the milling depth is shallow (less than 6cm), the water spray volume of the cooling head shall be reduced to facilitate the output of materials, so as to prevent the contact between cutting and milling materials and reduce the wear of cutting tools. Every 6-8 hours of operation, check the rotation and wear of the tool to ensure that the installed tool rotates freely in the tool holder.

合理的匹配速度

Reasonable matching speed

路面铣刨机的工作转速和转子转速也是该机的主要技术性能参数。工作速度直接影响机器的工作效率。由于受路面材料种类、沥青混合料强度、铣刨深度和环境温度的影响，工作速度一般设计为无级调节，以满足上述工况变化的要求。

The working speed and rotor speed of the pavement milling machine are also the main technical performance parameters of the machine. The working speed directly affects the working efficiency of the machine. Due to the influence of pavement material type, asphalt mixture strength, milling depth and ambient temperature, the working speed is generally designed as stepless adjustment to meet the requirements of the above working conditions.

保护腰带

Protective belt

为防止物料松动造成皮带磨损，保证转子空间的密封，限制磨碎旧料的粒度，同时保证皮带接收和皮带不受额外颠簸的可靠性，可以使用。采用皮带靴和分级控制梁。定期检查和更换皮带靴，采用合理的分级控制方案，可以充分保护皮带，减少皮带磨损，形成可靠稳定的收料机构。

It can be used to prevent belt wear caused by loose materials, ensure the sealing of rotor space, limit the particle size of grinded old materials, and ensure the reliability of belt receiving and belt free from additional bumps. Belt shoes and graded control beams are used. Regular inspection and replacement of belt boots, and the adoption of a reasonable hierarchical control scheme can fully protect the belt, reduce belt wear, and form a reliable and stable receiving mechanism.

定期清洁

Regular cleaning

冷再生机租赁厂家认为每个系统的清洁度对机器的可靠性非常重要。一些污垢和尖锐的固体颗粒被带入系统，随时可能发生摩擦、堵塞、卡住等故障，甚导致密封泄漏和损坏。温度升高，造成一系列恶性循环。

The rental manufacturer of cold regeneration machine thinks that the cleanliness of each system is very important to the reliability of the machine. Some dirt and sharp solid particles are brought into the system, which may cause friction, blockage, jamming and other failures at any time, and even lead to seal leakage and damage. The rising temperature causes a series of vicious cycles.

铣刨机未来会得到越来越广泛的应用，遵守操作规则，注重对铣刨机的科学使用、合理保养，让设备发挥大功效，对提高施工质量和效率，降低施工成本有着重要的意义，更多内容就来网站www.tclqgc.com关注了解吧！

The milling machine will be more and more widely used in the future. Following the operating rules, paying attention to the scientific use and reasonable maintenance of the milling machine, and making the equipment work effectively are of great significance to improve the construction quality and efficiency and reduce the construction cost. For more information, please visit www.tclqgc Com follow and understand!