九五至尊9599cww

冷再生施工和机械租赁业务
筑路架桥,奉献社会;以人为本,不断创新

服务热线

18264104888

新闻中心

首页>>新闻中心冷再生机机械的保养注意事项

冷再生机机械的保养注意事项

来源:/ 日期:2023-05-20 发布人:
一、清洗外表
1、 Cleaning the exterior
冷再生机在施工过程中会有大量的灰尘落到再生机的表面,包括施工中沾污的油迹等污染物,影响外观事小,更为严重的是成为腐蚀的诱发因素。
During the construction process of the cold regeneration machine, a large amount of dust will fall onto the surface of the regeneration machine, including pollutants such as oil stains during construction, which have a small impact on the appearance and, more seriously, become an inducing factor for corrosion.
冷再生机租赁厂家提醒,清洗工程机械的柴油机、底盘、工作装置的外表,除垢、除油保持再生机的外观整洁。清洗时严禁用高压、高温的水枪来冲洗防水要求较高的部位(特别是电器部分),以免造成电器部分的损坏。
Cold regeneration machine rental manufacturers remind us to clean the exterior of the diesel engine, chassis, and working devices of construction machinery, remove dirt and oil, and keep the appearance of the regeneration machine clean. It is strictly prohibited to use high-pressure and high-temperature water guns to wash parts with high waterproof requirements (especially electrical parts) during cleaning, in order to avoid damage to the electrical parts.
二、保养转子及其罩壳和滑靴
2、 Maintain the rotor and its casing and shoes
1.检查转子是否有水泥结垢等,及时清理灰尘,对需要割除、焊接的刀具及时更换;
1. Check if there is cement scaling on the rotor, clean the dust in a timely manner, and replace the cutting tools that need to be cut or welded in a timely manner;
2.清理转子罩壳上的灰尘,并在施工结束收车时将转子罩壳垫起地面5-10公分,防止雨雪的浸蚀;
2. Clean the dust on the rotor casing and pad the rotor casing 5-10 cm above the ground at the end of construction to prevent erosion by rain and snow;
3.检查滑靴,对已经磨损的滑靴部分进行补焊,螺纹处应涂抹黄油防锈。
3. Check the sliding shoes, repair welding the worn parts of the sliding shoes, and apply butter to the threads for rust prevention.
冷再生机租赁
三、减速机齿轮油的更换方式
3、 Replacement method of reducer gear oil
减速机油位及减速机油的检查:先切断电源,等待减速机冷却后打开放油螺塞,检查油是否充满,避免漏油,取油样,检查油色泽及粘度指数,如果油明显浑浊,建议尽快更换。新减速机使用后(500-1000)小时更换新油(将内部污油冲干净),其后每使用1500小时需要更换油一次,但是在使用过程中,仍需要检查油的质量,若油有老化、变质情况要随时更换。
Inspection of gearbox oil level and reducer oil: First cut off the power supply, wait for the gearbox to cool down, open the oil drain plug, check whether the oil is full to avoid oil leakage, take an oil sample, check the oil color and viscosity index. If the oil is significantly turbid, it is recommended to replace it as soon as possible. After the new gearbox is used (500-1000 hours), replace it with new oil (flush out the internal dirty oil). Afterwards, the oil needs to be replaced every 1500 hours of use. However, during use, the quality of the oil still needs to be checked. If the oil has aged or deteriorated, it should be replaced at any time.
冷再生机机械的保养注意事项就从这三个方面来讲解一番,希望能够给您好的帮助,更多事项就来我们的网站咨询吧!
The maintenance precautions for the cold regeneration machine machinery will be explained from these three aspects. We hope to provide you with good help. For more details, please visit our website Consult!

阅读/ Recommended reading

  冷再生机和路拌机在路面施工及维修中各有其独特的功能和适用场景,它们之间的主要区别体现在以下几个方面:  Cold recycling machines and road mi...

冷再生机出租对道路施工行业的影响 2024-12-18
如何选择冷再生机出租服务 2024-12-16
冷再生机出租:道路施工的新选择 2024-12-11
冷再生机租赁在土壤稳定中的应用与优势 2024-12-09

产品/ Recommended products