新闻中心
新闻资讯
联系我们
九五至尊9599cww
联系人:石总
电话:18264104888
地址:山东省济南市槐荫区经一路273号群盛华城
现今26吨压路机保养存在的误区!
来源:/ 日期:2023-04-19 发布人:
对于26吨压路机的维修保养十分重要,但是由于技术保养人员对保养工作存在的误区,致使26吨压路机性能更加不良。下面冷再生机租赁厂家从五个方面为您讲解一番:
The maintenance and upkeep of the 26 ton roller is very important, but due to misunderstandings among technical maintenance personnel, the performance of the 26 ton roller is even worse. The cold regeneration machine rental manufacturer will explain to you from five aspects:
1
one
润滑油定期地更换没有及时做到
Regular replacement of lubricating oil not achieved in a timely manner
像26吨压路机这样的重型机械,由于长期在重负荷的环境下工作,机械零件的磨损是比较严重的,而润滑油是保证其机械磨损降正常状态下的重要因素,也是保证26吨压路机正常工作的重要因素,26吨压路机在长期使用中,会导致机体的内部、油底壳中含有大量的机械磨损杂质,另外,长期使用的润滑油,若不及时更换,其中也会含有大量杂质,这样的状况既有可能会导致机械的磨损更加严重,因此,因此润滑油的不及时更换对机械的损害是很严重的。
Heavy machinery such as a 26 ton roller, due to long-term operation in a heavy load environment, has severe wear and tear on its mechanical components. Lubricating oil is an important factor in ensuring that its mechanical wear and tear are reduced to normal conditions, and it is also an important factor in ensuring the normal operation of the 26 ton roller. Long term use of the 26 ton roller can cause a large amount of mechanical wear impurities to be contained in the internal parts of the body and the oil pan. In addition, Long term lubricating oil, if not replaced in a timely manner, may also contain a large amount of impurities, which may lead to more severe mechanical wear. Therefore, the failure to replace lubricating oil in a timely manner can cause serious damage to the machinery.
2
two
维修时对螺栓非正常操作以及轮胎气压控制不到位
Abnormal operation of bolts and inadequate control of tire pressure during maintenance
维修人员在26吨压路机的维护保养工作中起到了为直接的作用,但是,一些维修技术人员在养护过程中,为了确保机械构件之间连接的稳定性,常常会将螺丝拧的过紧,或者是将轮胎的气压充的过足,这样的出发心态也是求得稳定,但是负面影响较为明显,机械衔接过于紧密、会造成螺栓的断裂滑丝现象,气压过高会造成轮胎张力过大,是十分不利于26吨压路机的正常使用的,存有一定的隐患。
The maintenance personnel have played a direct role in the maintenance and upkeep of the 26 ton road roller. However, some maintenance technicians often tighten the screws too tightly or inflate the tire pressure too much during the maintenance process to ensure the stability of the connection between mechanical components. This mentality also seeks safety and stability, but the negative impact is more obvious. The mechanical connection is too tight It can cause bolt breakage and slipping, and excessive air pressure can cause excessive tire tension, which is very detrimental to the normal use of a 26 ton roller and poses certain safety hazards.
3
three
26吨压路机水箱温度控制不当
Improper temperature control of the 26 ton roller water tank
26吨压路机的水箱温度控制直接影响到水箱设备――缸体的性能及耐久性。但是在工程运行过程中,机械的持久运行势必会消耗大量的水,往往在向水箱中加水的时候,水箱内的水温是十分高的,通常都是出于沸腾状态的,这时候,由于技术人员对水温落差的忽略,骤加冷水,导致水箱温度急剧下降,冷热的急剧变化,对箱体缸体是十分不利的,大大降低了其耐久性。
The temperature control of the water tank of a 26 ton roller directly affects the performance and durability of the water tank equipment - the cylinder body. However, in the process of engineering operation, the sustained operation of machinery will inevitably consume a large amount of water. Often, when adding water to the water tank, the water temperature inside the tank is very high, usually in a boiling state. At this time, due to the neglect of the water temperature drop by technical personnel, sudden addition of cold water leads to a sharp decrease in the temperature of the water tank, and the rapid changes in cold and hot water are very detrimental to the cylinder body of the box, greatly reducing its durability.
4
four
润滑油脂的不正确使用
Incorrect use of lubricating grease
26吨压路机的设备中,各自有其特殊的要求,其中,汽缸垫对密封性有高的要求。但是在安装汽缸垫的时候,是有高的要求的。一些技术人员在安装的时候,为了保证安装的顺利,往往会涂抹润滑油脂,在气缸盖螺栓拧紧的时候,由于物体间的挤压,部分润滑油脂会进入到汽缸水道中,气缸中的温度是高的,这样的话,油脂长期处于高温状态下,易碳化,碳化的后果会损坏汽缸垫,接着变会引起气缸的漏气,后果不堪设想。
Among the 26 ton roller equipment, each has its own special requirements, among which the cylinder gasket has high requirements for sealing. But when installing the cylinder gasket, there are high requirements. Some technical personnel often apply lubricating grease during installation to ensure smooth installation. When tightening the cylinder head bolts, due to the compression between objects, some of the lubricating grease will enter the cylinder water channel, and the temperature in the cylinder is high. In this way, the grease will be in a high-temperature state for a long time, which is prone to carbonization. The consequences of carbonization will damage the cylinder gasket, and then cause air leakage in the cylinder, which is unimaginable.
5
five
液压系统方面的操作及油品选择不当
Improper operation and oil selection in the hydraulic system
燃油的选择直接决定发动机的工作性能及效率,26吨压路机往往选择的是轻柴油,轻柴油也有不同的等级型号,不同的型号使用上性能差别很大,但是一些技术人员在选择时往往考虑不周,导致选择了不适合的油,给后期的养护带来了不少困难。液压系统是其工作中的核心系统,这里对系统频率的控制,机械马力的控制,对机械的性能耐久关键,操作的马虎不当对机械的长久运行是十分不利的。
The selection of fuel directly determines the working performance and efficiency of the engine. 26 ton road rollers often choose light diesel, which also has different grades and models. The performance of different models varies greatly, but some technical personnel often do not consider the selection carefully, leading to the selection of unsuitable oil, which brings many difficulties to later maintenance. The hydraulic system is the core system in its operation, and the control of system frequency and mechanical horsepower is crucial for the durability of mechanical performance. Improper operation is very detrimental to the long-term operation of the machinery.
使用说明书中对压路机的等级养护分为一二三级,一级保养工作类似于走合期保养,主要对机械部件之间的连接,润滑状态及时更新,排除工作一段时间后的薄弱环节。二级保养主要的工作时检查和调整,这时候的检查调整是的,主要目的是保证设备在较长的一段时间内有一个良好的状态。三级保养工作时细致入微的,要将设备全盘拆卸,整体清洗,整体润滑,及时更换,也会附加一些维修工作,保证设备发挥其价值。更多需求就来我们网站咨询了解吧!
In the user manual, the level maintenance of the roller is divided into one, two, and three levels. The first level maintenance work is similar to the maintenance during the running in period, mainly updating the connection and lubrication status between mechanical components in a timely manner to eliminate weak links after working for a period of time. The main task of secondary maintenance is to inspect and adjust, which is comprehensive and aims to ensure that the equipment is in good condition for a long period of time. During the third level maintenance work, the equipment should be thoroughly disassembled, cleaned, lubricated, and replaced in a timely manner. Additionally, some maintenance work will be added to ensure that the equipment can fully realize its value. Come to our website for more needs Consult and understand!
下一篇:冷再生机设备如何用于路面施工 上一篇:就地冷再生机是什么及技术适用条件
阅读/ Recommended reading
- 冷再生机出租对道路施工行业的影响 2024-12-18
- 如何选择冷再生机出租服务 2024-12-16
- 冷再生机出租:道路施工的新选择 2024-12-11
- 冷再生机租赁在土壤稳定中的应用与优势 2024-12-09
冷再生机和路拌机区别
[2018-08-23]
冷再生机和路拌机在路面施工及维修中各有其独特的功能和适用场景,它们之间的主要区别体现在以下几个方面: Cold recycling machines and road mi...