一、减速机部分

1、 Reducer part

目前冷再生机配置的是美国原装进口减速机，是动力传输非常重要的部件，对再生机的整体性能起着举足轻重的作用，它内置在转子内，作用是减小转速，增加扭矩。

Currently, the cold regeneration machine is equipped with a reducer imported from the United States, which is a very important component for power transmission and plays a crucial role in the overall performance of the regeneration machine. It is built into the rotor to reduce rotational speed and increase torque.

减速机

Reducer

减速机的保养必须由专门人员操作或指导，保养周期是500小时，之后保养周期是1000小时。

The maintenance of the gear unit must be operated or guided by specialized personnel. The first maintenance interval is 500 hours, and the subsequent maintenance interval is 1000 hours.

减速机盖

Gear unit cover

冷再生机租赁认为其减速机在使用时温度非常高，后盖为‘o'型圈密封，容易渗漏；减速机的油封容易被再生料里的铁丝等坚硬物破坏造成渗油。

The cold regeneration machine rental believes that the temperature of its reducer is very high when it is used, and the rear cover is sealed with an 'o' ring, which is prone to leakage; The oil seal of the reducer is easily damaged by hard objects such as iron wires in the recycled material, causing oil leakage.

二、转子及罩壳部分

2、 Rotor and casing part

（1）施工过程中注意观察刀头磨损情况，发现松动、脱落、折损等情况应及时处理和更换。否则容易造成刀座的磨损，刀座的更换比较麻烦，需要气割、电焊等工具，有时工地条件不具备，或焊接水平达不到，直接影响使用，可更换的刀座虽说方便，但会增加使用成本。

(1) During the construction process, pay attention to observing the wear of the cutting head, and promptly handle and replace any loose, detached, or damaged situations. Otherwise, it is easy to cause wear of the knife holder, and the replacement of the knife holder is relatively troublesome, requiring tools such as gas cutting and electric welding. Sometimes the site conditions are not available or the welding level cannot be reached, which directly affects the use. Although replaceable knife holders are convenient, they will increase the use cost.

（2）更换刀头时可用刀头攻击器将旧刀头敲出，新刀头用铁锤敲入刀座孔内即可。焊接刀座时注意焊接角度，否则会导致再生层深浅不一，造成刀具提前磨损等情况，从而会增加发动机负荷，造成不必要的动力输出。

(2) When replacing the cutter head, use a cutter head attacker to knock out the old cutter head, and use a hammer to knock the new cutter head into the cutter holder hole. Pay attention to the welding angle when welding the cutter holder, otherwise the depth of the regeneration layer may vary, resulting in premature wear of the cutter, and other situations, which may increase engine load and cause unnecessary power output.

（3）铣刨转子、铣刨转子罩壳等工作装置，每天施工结束后应进行清洗，这样做可以避免以下情况的发生：

(3) Working devices such as milling rotors and milling rotor casings should be cleaned after construction every day to avoid the following situations:

①罩壳上的水喷孔堵塞，次日工作时水分不均;

① The water spray hole on the cover is blocked, resulting in uneven water content during the next day's work;

②再生料粘附在铣刨转子上极难清理掉，影响拌合效果;

② The adhesion of recycled materials to the milling rotor is extremely difficult to remove, affecting the mixing effect;

③再生料粘附在刀头、刀座上，导致更换困难;

③ The recycled material adheres to the cutter head and cutter seat, resulting in difficulty in replacement;

（4）滑靴的保养。对已经磨损的滑靴部分进行补焊，螺纹处应涂抹黄油防锈。更多相关事项就来我们网站咨询了解吧！

(4) Maintenance of sliding shoes. Repair welding shall be carried out on the worn sliding shoes, and the threads shall be coated with butter to prevent rust. For more related matters, please visit our website Consult and understand!