摊铺机摊铺时加速摊铺厚度是增加还是减少？实际上摊铺机在摊铺的过程中，要求是匀速的，熨平板是浮动在摊铺物料上的。

Does the accelerated paving thickness increase or decrease when the paver is paving? In fact, during the paving process, the paver requires a constant speed, and the screed is floating on the paving material.

冷再生机出租厂家认为，换句话说，此时熨平板的合力是零，一旦加速，速度增加了，单位时间内熨平板摊铺所需的物料没有及时增加（机器反应有个过程），物料平均到走过的距离上就是减少了，所以摊铺的路面厚度减小了，此时速度稳定后，熨平板有重新达到平衡的要求，厚度会慢慢的增加到原来的厚度。

The manufacturer of the cold recycling machine believes that, in other words, the resultant force of the screed is zero at this time. Once accelerated, the speed increases, and the material required for screed paving does not increase in time per unit time (there is a process of machine reaction). As a result, the average distance traveled by the material decreases, so the thickness of the paved road surface decreases. At this time, when the speed stabilizes, the screed has the requirement to regain balance, The thickness will gradually increase to the original thickness.

在现实的施工中，摊铺与速度、温度、物料配合比，施工的严谨程度都有关系。

In real construction, paving is related to speed, temperature, material mix ratio, and the rigor of construction.

摊铺机的作业速度以输分料保持匀速旋转来确定摊铺大行走速度。有规律的相应提高行走速值，夯锤数值，输料数值，分料数值，使有规律的同时调高和调低，大的摊铺速度不能使刮板和螺旋快速旋转，这样会使摊铺面离析。

The operating speed of the paver is determined by maintaining a uniform rotation of the conveying and distributing materials to determine the large paving speed. Regularly increase the traveling speed value, rammer value, material delivery value, and material separation value accordingly, so as to regularly increase and decrease them simultaneously. Large paving speeds cannot cause rapid rotation of the scraper and spiral, which can cause segregation of the paving surface.

刮板和螺旋速度调整：根据摊铺厚度和宽度，摊铺速度三者相关，在主控制器中找出相应界面，先按50%设定，然后在摊铺过程中，再根据摊铺速度调整。

Adjustment of scraper and spiral speed: According to the correlation between paving thickness, width, and paving speed, find the corresponding interface in the main controller, set it by 50%, and then adjust it according to the paving speed during the paving process.

摊铺机摊铺过程中要能连续摊铺,不能随意停机,以免影响路面的平整度,当出现意外情况必须停车时,要将摊铺机熨平板的防沉降锁打开,以免熨平板下沉,再次起步时要将摊铺机熨平板达到防爬锁打开,以免熨平板前方的沥青料温度太低会将熨平板抬起,增大摊铺厚度，影响路面的平整度。

During the paving process of the paver, it is necessary to be able to continuously pave and not stop at will to avoid affecting the flatness of the road surface. When an unexpected situation occurs and it is necessary to stop, the anti settlement lock of the paver's screed plate should be opened to prevent the screed plate from sinking. When starting again, the paver's screed plate should be opened to prevent the low temperature of the asphalt material in front of the screed plate from lifting the screed plate, increasing the paving thickness, and affecting the flatness of the road surface.

就摊铺机的操作而言，在摊铺过程中，还应注意尽量保持摊铺的连续性和稳定速度，严禁时快时慢，尽量减少停机次数，严禁运输车倒车时碰撞摊铺机。必要时可以通过两边放线找平，利用纵坡摊铺机纵坡仪，走钢丝来控制平整度。

In terms of the operation of the paver, during the paving process, attention should also be paid to maintaining the continuity and stable speed of paving as much as possible. It is strictly prohibited to be fast and slow, minimize the number of stops, and prohibit the transport vehicle from colliding with the paver when reversing. If necessary, the flatness can be controlled by setting out and leveling on both sides, using the longitudinal slope meter of the longitudinal slope paver, and walking steel wires.

摊铺机摊铺时加速摊铺厚度相关问题就讲解到这里了，您对此有怎样的疑惑或者需求，就来我们网站咨询了解吧！

That's all about accelerating the paving thickness when paving with a paver. If you have any doubts or needs about this, please come to our website Consult and understand!