在使用冷再生机的时候，若是发生了搅拌不均匀这一状况的话，那么就需要引起大家注意了，因为这将会影响到冷再生机的使用效果，所以还是需要及时的采取措施来进行解决，这样的话才可以有效的解决搅拌不均匀的现象，下面冷再生机出租厂家来讲解下，冷再生机搅拌不均匀的解决方法吧。

If the uneven mixing occurs during the use of cold regenerator, we should pay attention to it, because it will affect the use effect of cold regenerator, so we still need to take timely measures to solve it, so that we can effectively solve the uneven mixing phenomenon. Now let the cold regenerator rental manufacturer explain the solution to the uneven mixing of cold regenerator.

一、减少冷再生机各部件的摩擦阻力：

1、 Reduce the friction resistance of various parts of the cold regenerator:

严格执行机械技术保养制度，按规定进行润滑，以降低运行机构的阻力损失，如鼓筒轮箍与滚子表面间的滚动摩擦阻力，滚子的支承轴与轴套之间的摩擦阻力，以及提升料斗的阻力等，从而提高机械效率。

Strictly implement the mechanical technical maintenance system and lubricate as required to reduce the resistance loss of the operating mechanism, such as the rolling friction resistance between the drum tyre and the roller surface, the friction resistance between the roller bearing shaft and the shaft sleeve, and the resistance of the lifting hopper, so as to improve the mechanical efficiency.

二、减少冷再生机无效负荷：

2、 Reduce the invalid load of cold regenerator:

减少机械无效负荷可从加料、搅拌和出料工序采取措施：加料斗卸料完毕应及时放下，以减少振动的能耗，正确掌握搅拌时间，在保证混凝土质量的前提下，适时卸出，从而减少功率消耗，卸料干净、如果搅拌筒粘料太多，应进行清理、残料过多不但影响生产率，而且增加功率消耗。

Measures can be taken to reduce the mechanical invalid load from the feeding, mixing and discharging processes: the feeding hopper shall be put down in time after discharging to reduce the energy consumption of vibration, correctly control the mixing time, and discharge in time on the premise of ensuring the concrete quality, so as to reduce the power consumption. The discharge is clean, and if the mixing drum has too much sticking, it should be cleaned. Excessive residue not only affects the productivity, but also increases the power consumption.

三、缩短冷再生机空转时间：

3、 Reduce idling time of cold regenerator:

除了按操作规程进行起动和停机保养的空转时间以外，在施工过程中，应尽量缩短机械空转时间、对冷再生机，如因供料不及时或棍凝土运输、浇注等原因造成空运转在1分钟以上者、应空载停机、节约电能，对于拌和机，则应及时调节油门，使内燃机怠速运行、若空转时间较长，也应停机、降低油耗。

In addition to the idle time for starting and stopping maintenance according to the operating procedures, during the construction process, the idle time of the machinery should be shortened as much as possible. For the cold regenerator, if the idle time is more than 1 minute due to the untimely supply of materials or the transportation and pouring of stick concrete, the machine should be stopped without load to save electric energy. For the mixer, the accelerator should be adjusted in time to make the internal combustion engine run at idle speed. If the idle time is long, the machine should also be stopped Reduce fuel consumption.

四、其它措施：

4、 Other energy-saving measures:

可参照电动机或内燃机的经济使用措施，为了能够保证冷再生机的使用寿命，还需要对其进行保养，冷再生机进料侧拌叶长期使用，可能会出现变形或者损害的现象。出现变形的话，只能对拌和机拌叶进行修复或者更换，拌和机出料侧拌叶出现变形或者损害的现象，对变形的叶片进行修复或更换。

Refer to the economic use measures of electric motor or internal combustion engine. In order to ensure the service life of cold regeneration, it is also necessary to maintain it. The mixing blade at the feed side of the cold regeneration machine may be deformed or damaged if it is used for a long time. In case of deformation, the mixing blade of the mixer can only be repaired or replaced. If the mixing blade at the discharge side of the mixer is deformed or damaged, the deformed blade can be repaired or replaced.

为了能够保证冷再生机的使用寿命，还需要对其进行保养，日常的检查与维护工作必不可少，更多相关内容就来我们网站咨询了解！

In order to ensure the service life of cold reinvigoration, it is also necessary to maintain it. Daily inspection and maintenance work is essential. More relevant content is available on our website Consult and understand!