新闻中心
新闻资讯
联系我们
九五至尊9599cww
联系人:石总
电话:18264104888
地址:山东省济南市槐荫区经一路273号群盛华城
冷再生机使用期间为什么会打滑?
来源:/ 日期:2022-11-11 发布人:
客户在冷再生机出租使用过程中,不可避免地会出现消耗和磨损,其中,冷再生机输送带特别容易出现问题,运行时间长,可能出现打滑现象,影响工作效率。让冷再生机出租厂家带我们一起来分析下打滑的原因和解决办法。
In the process of renting and using the cold regenerator, the customer will inevitably encounter consumption and wear. Among them, the conveyor belt of the cold regenerator is particularly prone to problems, running for a long time, and may slip, affecting the working efficiency. Let the cold regeneration machine rental manufacturer take us to analyze the causes and solutions of slipping.
1、初始张力太小。
1. The initial tension is too small.
输送带离开滚筒的张力不够,会引起皮带打滑。一般来说,这种情况是在启动时发生的。如果你想解决它,你要调整张力装置和增加初始张力。
The tension of the conveyor belt leaving the drum is not enough, which will cause the belt to slip. Generally, this happens at startup. If you want to solve it, you need to adjust the tension device and increase the initial tension.
2、摩擦力是不够的。
2. Friction is not enough.
传动滚筒与输送带之间的摩擦力不足以引起滑动。造成这种现象的主要原因是输送带上的水或环境潮湿。解决方法:在气缸中加入一些松香末。注意不要用手而应用鼓风设备吹入,以免发生事故。
The friction between the drive drum and the conveyor belt is not enough to cause sliding. The main reason for this is the water on the conveyor belt or the humid environment. Solution: Add some rosin powder into the cylinder. Be careful not to blow in by hand with air blower to avoid accidents.
3、轴承损坏
3. Bearing damage
尾部滚子轴承损坏或不旋转。造成损坏的原因是机器尾部太浮、太沉,不能及时修理和更换损坏的或不灵活的部件,这导致由打滑引起的阻力增加。
The rear roller bearing is damaged or does not rotate. The cause of damage is that the tail of the machine is too floating and heavy to repair and replace damaged or inflexible parts in time, which leads to increased resistance caused by slipping.
4、起步太快。
4. Start too fast.
起动速度太快,不能打滑。这个时候可慢速启动。如果使用鼠笼电机,则可以移动两次,然后被,还可以有效地克服打滑现象。
The starting speed is too fast to slip. It can be started slowly at this time. If a squirrel cage motor is used, it can be moved twice and then activated, and can also effectively overcome the slip phenomenon.
5、输送带负荷过大。
5. The conveyor belt is overloaded.
输送带的负荷过大,超过电机能力也会打滑。打滑的优点是保护电机。否则,电动机将长期燃烧。但对于运行来说则是打滑事故。
If the load of the conveyor belt is too large, it will slip when exceeding the motor capacity. The advantage of slipping is to protect the motor. Otherwise, the motor will burn for a long time. But for operation, it is skid accident.
The above is an introduction to the reasons and methods for the slipping of the cold regeneration machine when renting. I hope it will be helpful to you. Thank you for your reading. If you want to know more, please click our Official website.
下一篇:冷再生机对于施工质量的要求 上一篇:两个简单的冷再生机养护措施
阅读/ Recommended reading
- 冷再生机租赁:就地冷再生施质量控制要点 2024-09-21
- 冷再生机租赁:维特根冷再生机W 240 CR,用途广泛显神功 2024-09-15
- 冷再生机租赁:就地冷再生施工技术的原理及其特点分析 2024-09-04
- 冷再生机租赁——保养注意事项 2024-09-02
冷再生机租赁:路拌/冷再生机,让你的施工过程始终“开挂”
[2018-08-23]
作为路面施工装备中的一员 路拌/冷再生机一直以来均在路面解决方案里占有重要作用。而RS500路拌/冷再生机,作为一款性能出色的路面养护设备,更是行业里同类产品中的佼佼者。发动...