胶轮压路机施工效率高，压实效果好，得到了工程行业用户的好评，该设备在使用上有许多与振动压路机等工程机械不同的注意事项，在这里我们谈一谈胶轮压路机轮胎的保养。

The rubber tyred roller has high construction efficiency and good compaction effect, which has been highly praised by users in the engineering industry. There are many precautions different from vibratory roller and other construction machinery in the use of this equipment. Here we talk about the maintenance of rubber tyred roller tires.

我们要知道胶轮压路机常配的轮胎分为充气轮胎和实心轮胎，者两种轮胎使用上有所不同，通常情况下，胶轮压路机冲击压实轮会配备充气轮胎，这是应为，胶轮压路机的四个胶轮轮胎不单单起着短途运输转场的作用，在施工过程中，这四个轮胎还起着减震的作用。

We need to know that the tires often equipped with rubber tyred rollers are divided into pneumatic tires and solid tires, which are different in use. Generally, the impact compaction wheels of rubber tyred rollers will be equipped with pneumatic tires. This is because the four rubber tyred tires of rubber tyred rollers not only play the role of short-distance transportation transfer, but also play the role of shock absorption during construction.

胶轮压路机的四个胶轮轮胎在施工过程中一蹦一跳，对胶轮压路机机架上的橡胶减震有一定的保护作用，许多用户在充气轮胎泄气或是被扎烂后不及时处理，就会发现机架上的橡胶减震套也会很快受损，进而有引发出其他问题。

The four rubber tires of the rubber tyred roller jump and jump during the construction process, which has a certain protective effect on the rubber damping on the frame of the rubber tyred roller. Many users do not deal with it in time after the pneumatic tire is deflated or punctured, and they will find that the rubber damping sleeve on the frame will also be damaged soon, which will lead to other problems.

充气轮胎适合大部分冲击碾压施工环境，但遇到冲击碾压石方或是建筑垃圾时，石方或建筑垃圾的尖锐角料、以及建筑垃圾中的钢筋等物质，很容易把轮胎扎烂，这时，好换上不怕扎的实心轮胎。

Pneumatic tires are suitable for most impact rolling construction environments, but when encountering impact rolling stone or construction waste, the sharp corner materials of stone or construction waste, as well as the reinforcement in construction waste, are easy to puncture the tires. At this time, it is good to replace them with solid tires that are not afraid of puncture.

冷再生机租赁厂家认为实心轮胎非常好用，但它会大大削弱轮胎的减震效果，降低了对机架缓冲的保护作用，而且，实心轮胎在碰到尖锐角料时或是强转弯扭力大时，也会掰掉块儿。

The rental manufacturer of the cold regenerator thinks that the solid tire is very easy to use, but it will greatly weaken the shock absorption effect of the tire and reduce the protective effect on the buffer of the frame. In addition, the solid tire will also break off when it encounters sharp corners or strong turning torque.

胶轮压路机由于承载量大，且轮胎跨度小太居中，急转弯时会受到很大的扭力，很容易损伤，因此，胶轮压路机在转弯时一定要慢行，尽量多调整加大转弯半径，同时，胶轮压路机载重量大，充气轮胎气压应保持在0.6~0.8Mpa左右，还要注意短途转场行驶距离不易一次性过大，一般要求大约3左右进行一次轮胎降温，否则很有可能会造成爆胎或橡胶过热软化。

Due to its large bearing capacity, small and medium tire span, the rubber tyred roller will suffer great torsion when turning sharply, which is easy to be damaged. Therefore, the rubber tyred roller must slow down when turning, and adjust as much as possible to increase the turning radius. At the same time, the rubber tyred roller has a large airborne weight, and the air pressure of the inflated tire should be maintained at about 0.6~0.8mpa. It is also important to note that the driving distance of short-distance transition is not easy to be too large at one time, Generally, it is required to cool the tire for about 3 kilometers, otherwise it is likely to cause tire burst or rubber overheating and softening.

胶轮压路机的轮胎在施工过程中与地面的接触点以及转动方向是随机的，但胶轮压路机在施工过程中必须要遵循错轮回转原则及错峰碾压原则，因此，这种条件下胶轮压路机的轮胎有时会“碰巧”与后桥锁紧螺帽的锁紧方向相反，因此，每次停车检查各连接部分的紧固零件是否有松脱现象时，也都要看看小轮毂的锁紧螺帽有没松动，也不要忘记检查轮胎气压，检查轴承是否发热，如有问题，要立即处理。

The contact point and rotation direction of the tire of the rubber tyred roller with the ground during the construction process are random, but the rubber tyred roller must follow the principle of staggered rotation and staggered peak rolling during the construction process. Therefore, under this condition, the tire of the rubber tyred roller sometimes "happens" to be opposite to the locking direction of the rear axle locking nut. Therefore, every time you stop to check whether the fastening parts of each connecting part are loose, Also check whether the locking nut of the small wheel hub is loose, and don't forget to check the tire pressure and whether the bearing is hot. If there is a problem, it should be dealt with immediately.

以上就是今天为大家介绍的关于问题以及注意事项的全部内容，希望对大家能有所帮助，想要了解更多内容可以电话联系我们或者关注我们的网站，我们的工作人员会及时与您取得联系。

The above is all about the problems and precautions introduced to you today. I hope it can help you. If you want to know more, you can contact us by phone or follow our website , our staff will contact you in time.