新闻中心
新闻资讯
联系我们
九五至尊9599cww
联系人:石总
电话:18264104888
地址:山东省济南市槐荫区经一路273号群盛华城
当移动破碎站的产量降低时原因是什么?
来源:/ 日期:2022-07-04 发布人:
移动破碎站吸引人的特点是其强大的生产能力。但是,当移动破碎站的产量降低时,原因是什么,如何解决呢?
The attractive feature of mobile crushing station is its strong production capacity. However, when the output of mobile crushing station decreases, what is the reason and how to solve it?
1.腔体内堆积了太多的材料。
1. Too much material is accumulated in the cavity.
如果物料过湿,则会堆积在型腔内部,这会在加工物料时造成堵塞,从而导致设备效率低下。 如果物料太湿,应进行,然后再进行破碎工作。
If the material is too wet, it will accumulate in the cavity, which will cause blockage when processing the material, resulting in low efficiency of the equipment. If the material is too wet, it should be dehumidified before crushing.
2.振动不稳定。
2. Unstable vibration.
振动不规则以及移动破碎站的振动:锤子可能存在问题。必须及时检查并在必要时更换锤子。轴承和齿轮联轴器也可能存在问题。应及时更换以使振动平稳。
Irregular vibration and vibration of mobile crushing station: there may be problems with the hammer. The hammer must be checked in time and replaced if necessary. There may also be problems with bearings and gear couplings. It should be replaced in time to make the vibration stable.
3.成品尺寸不规则。
3. The size of the finished product is irregular.
当颗粒太细时,钳口中可能有太多锤子或牙齿。然后应减少时间。当颗粒太粗糙时,锤子或钳口可能会减少,应立即增加。传送带太松或电压不足也可能。在这种情况下,请调节传送带的松紧度,检查电压功率,然后调节适当的电压。
When the particles are too fine, there may be too many hammers or teeth in the jaws. Then reduce the time. When the particles are too rough, the hammer or jaw may be reduced and should be increased immediately. It is also possible that the conveyor belt is too loose or the voltage is insufficient. In this case, please adjust the tightness of the conveyor belt, check the voltage power, and then adjust to the appropriate voltage.
4.轴和轴承过热。
4. Shaft and bearing overheat.
移动式破碎站的轴承受了机器的全部负荷。如果轴承温度过高,可能是机油不足,则需要添加适量的润滑油。如果润滑油被污染,则需要清洁轴承,然后更换润滑油;如果轴承损坏,则需要更换轴承并降低温度。
The shaft of the mobile crushing station bears the full load of the machine. If the bearing temperature is too high, it may be due to insufficient engine oil, and an appropriate amount of lubricating oil needs to be added. If the lubricating oil is contaminated, it is necessary to clean the bearing and then replace the lubricating oil; If the bearing is damaged, replace the bearing and reduce the temperature.
如果移动破碎站的润滑效果不好,容易磨损的零件不能及时更换,维护不完善,上述所有因素都会导致生产不良。如果设备出现故障并进行维护,将会减少产量。
If the lubrication effect of the mobile crushing station is not good, the easily worn parts cannot be replaced in time, and the maintenance is not perfect, all the above factors will lead to poor production. If the equipment fails and is maintained, the production will be reduced.
冷再生机租赁人员认为如果根据润滑周期对移动式破碎站进行润滑,将会延长移动式破碎站的使用寿命。
The leasing personnel of the cold regenerator believe that if the mobile crushing station is lubricated according to the lubrication cycle, the service life of the mobile crushing station will be prolonged.
The above is the relevant content of the question answer. I hope it can help you. If you still have any questions about this problem, you are welcome to follow our website And consult our staff, will serve you wholeheartedly.
下一篇:道路就地冷再生工艺有着诸多优点 上一篇:26吨压路机的“油”错误保养几方面
阅读/ Recommended reading
- 冷再生机出租对道路施工行业的影响 2024-12-18
- 如何选择冷再生机出租服务 2024-12-16
- 冷再生机出租:道路施工的新选择 2024-12-11
- 冷再生机租赁在土壤稳定中的应用与优势 2024-12-09
冷再生机和路拌机区别
[2018-08-23]
冷再生机和路拌机在路面施工及维修中各有其独特的功能和适用场景,它们之间的主要区别体现在以下几个方面: Cold recycling machines and road mi...