新闻中心
新闻资讯
联系我们
九五至尊9599cww
联系人:石总
电话:18264104888
地址:山东省济南市槐荫区经一路273号群盛华城
天气清冷之前冷再机怎么保养一下?
来源:/ 日期:2021-10-26 发布人:
1、将设备启动移已选好场地,将转子罩弹簧销轴取出,再将转子放置低点,切记不可悬置或有吃力现象,造成大臂油缸销轴取不出来,油管泄压易出危险。
1. Move the equipment startup to the selected site, take out the spring pin shaft of the rotor cover, and then place the rotor at the lowest point. Remember not to suspend or have difficulty, resulting in the failure to take out the pin shaft of the boom oil cylinder and the danger of oil pipe pressure relief.
2、拆卸油管和转子马达的保护罩壳。
2. Remove the protective cover of oil pipe and rotor motor.
3、将马达到工作泵的6根油管在大臂连接处全部拆卸开,并用卫生纸和塑料带将接口全部封紧,预防进入灰尘及杂物,并取下连接钢管。
3. Remove all 6 oil pipes from the motor to the working pump at the boom connection, seal all the interfaces with toilet paper and plastic tape to prevent dust and sundries, and remove the connecting steel pipe.
4、卸掉马达上的螺栓,并取下马达,注意需要两个人必须轻拿轻放。
4. Remove the bolts on the motor and remove the motor. Note that two people must handle it gently.
5、将转子罩壳所有的连接杆拆卸,取下销轴。
5. Remove all connecting rods of the rotor housing and remove the pin shaft.
6、将连接两个大臂与固定横杆上的螺栓拆卸掉,只留两边上面的4个。
6. Remove the bolts connecting the two boom and the fixed cross bar, leaving only 4 on both sides.
7、拆掉横杆和车体连接的4个螺栓,上下面做好标记,方便安装。
7. Remove the 4 bolts connecting the cross bar and the vehicle body, and mark the upper and lower parts for easy installation.
8、用吊车挂转子一侧的大臂处,另一侧挂马达后侧的销轴,先提升尽大量向一侧移动,然后将两根钢丝绳均挂到出来的那一侧,拖外面。
8. Hang the boom on one side of the rotor with a crane, and hang the pin shaft at the back of the motor on the other side. First lift and move to one side as much as possible, and then hang both steel wires to the side out and drag them to the outside.
9、卸掉滑靴,吊出转子罩。
9. Remove the sliding shoes and lift out the rotor cover.
10、卸掉大臂与横杆和转子的连接处的螺栓,吊出大臂,放置一边。
10. Remove the bolts at the connection between the boom and the cross bar and the rotor, lift out the boom and place it aside.
11、卸掉减速机固定螺丝,并用撬棍插入轴套压住,用吊车吊出减速机,放置一边,检查有无渗漏现象。
11. Remove the fixing screws of the reducer, insert the crowbar into the shaft sleeve and press it, lift out the reducer with a crane, place it aside and check for leakage.
12、放开减速机的两个油堵,放净废油。因两个油堵成90度角,在加注新油时,减速机平放的基础上必须让注油孔在高点,直到观察孔漏油为止,然后将油堵缠上生料带上紧,如油堵是无‘O’型圈的类型,需在生料带的外面涂抹密封胶,观察12小时后有无渗漏现象。
12. Release the two oil plugs of the reducer and drain the waste oil. Since the two oil plugs form a 90 degree angle, when filling new oil, the reducer must be placed horizontally, and the oil filling hole must be at the highest point until the observation hole leaks oil, and then wrap the oil plug with the raw material belt to tighten it. If the oil plug is of the type without 'o' ring, it is necessary to apply sealing glue on the outside of the raw material belt and observe whether there is leakage after 12 hours.
13、将以上步骤反之,安装完毕。在安装的过程中,大臂、马达、减速机的固定螺栓均需涂抹紧固胶,马达与减速机结合面涂抹密封胶。
13. Reverse the above steps to complete the installation. During installation, the fixing bolts of boom, motor and reducer shall be coated with fastening glue, and the joint surface of motor and reducer shall be coated with sealant.
以上就是冷再生机租赁为大家介绍的内容,感谢您在百忙之中查看我公司的信息内容,如果您想要了解的更多,欢迎您来电进行咨询!
The above is the lease of cold regenerator Thank you for checking the information of our company in your busy schedule. If you want to know more, you are welcome to call for consultation!
下一篇:冷再生机水稳层施工技术要注意什么? 上一篇:冷再生机道路维修起到是什么作用?
阅读/ Recommended reading
- 冷再生机出租对道路施工行业的影响 2024-12-18
- 如何选择冷再生机出租服务 2024-12-16
- 冷再生机出租:道路施工的新选择 2024-12-11
- 冷再生机租赁在土壤稳定中的应用与优势 2024-12-09
冷再生机和路拌机区别
[2018-08-23]
冷再生机和路拌机在路面施工及维修中各有其独特的功能和适用场景,它们之间的主要区别体现在以下几个方面: Cold recycling machines and road mi...